View FH33MHJ-65S-04SH_6972918.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1 0.4mm,0.5mm,1mm pitch, 1.2mm above the board, flexible printed circuit & flexible flat cable zif connectors fh33 series 2007.4 17mm features 1. low-profile, small pcb mounting area narrow width of only 2.5 mm reduced the board footprint by approximately 17% to 57%, as compared to several similar fh series hrs connectors. 2. various contact pitch (0.4mm, 0.5mm, 1mm pitch) available in addition to standard 0.5mm pitch, 0.4mm pitch, 1mm pitch also available. 3. increased fpc/ffc retention force _ in the horizontal direction: approximately 2.0 times (compared to 0.5mm pitch fh12 series.) _ in the vertical direction: approximately 1.7 times (compared to 0.5mm pitch fh19 series.) 4. conductive traces on the pcb can run under the connector no exposed contacts on the bottom of the connector. 5. one finger operation of the actuator proven (in several other hiroses connectors) flip-lock? rotating actuator assures reliable mechanical and electrical connection with fpc/ffc, confirming it with a definite tactile feel. 6. easy fpc insertion and reliable electrical connection proven flip lock actuator allows easy insertion of fpc/ffc and provides a tactile sensation when fully closed, confirming complete electrical and mechanical connection. 7. accepts standard fpc thickness 0.3mm thick standard flexible printed circuit (fpc) and flexible flat cable (ffc) can be used. 8. board placement with automatic equipment flat upper surface and tape and reel packaging facilitate vacuum pick-up and placement. standard reel packaging contains 5000 connectors. 9. halogen-free * (fh33j series) *as defined by iec61249-2-21 br-900ppm maximum, cl-900ppm maximum, cl + br combined-1,500ppm maximum small size can be mounted over conductive traces. no exposed contacts on the bottom of the connector 1.2mm 2.5mm 3 3 4 simple operation locked condition fpc actuator actuator actuator fpc 1 2 [ 30 pos. ] metal fittings (leadless) 1 open the actuator 2 insert fpc 3 close the actuator 4 fpc connected increased fpc retention force 2012.3
----- ----- temperature : -55? / + 15? to + 35? / + 85? / + 15? to + 35? time : 30 / 2 to 3 / 30 / 2 to 3 (minutes) 5 cycles reflow : at the recommended temperature profile manual soldering : 350? 10? for 5 seconds 1 ma 20 cycles 500 m? min. no flashover or insulation breakdown. 100 v dc 150 v ac /one minute, 120 v ac /one minute(0.4mm pitch type) 50 m? max. 100 m? max(0.4mm pitch type). * including fpc conductor resistance contact resistance: 50 m? max. 100 m? max(0.4mm pitch type). no damage, cracks, or parts dislocation. no electrical discontinuity of 1s or more. contact resistance: 50 m? max. 100 m? max(0.4mm pitch type). no damage, cracks, or parts dislocation. frequency: 10 to 55 hz, single amplitude of 0.75 mm, 10 cycles in each of the 3 directions. acceleration of 981 m/s 2 , 6 ms duration, sine half-wave waveform, 3 cycles in each of the 3 axis contact resistance: 50 m? max. 100 m? max(0.4mm pitch type). insulation resistance: 50 m? min. no damage, cracks, or parts dislocation. 96 hours at 40? and humidity of 90% to 95%. no deformation of components affecting performance. materials ordering information fh 33 m h j - 12 ( 6 ) s b - 1 sh ( 10 ) series name:fh series no:33 blank:0.5mm pitch,1mm pitch m:0.4mm pitch 1 2 material lcp pps lcp pa lcp pps phosphor bronze pa color:beige color:deep brown color:beige color:black color:beige color:deep brown color:beige color:black gold flash plated pure tin reflow plated ul94v-0 finish remarks insulator fh33 series fh33j series fh33m series fh33mhj series contacts metalfittings part product specifications ratings current rating 0.5 a (0.4mm pitch type 0.4a) voltage rating 50 v ac (0.4mm pitch type 40v ac) operating temperature range -55 ? to +85? (note 1) operating humidity range relative humidity 90% max. (no condensation) storage temperature range -10? to +50? (note 2) storage humidity range relative humidity 90% max. (no condensation) recommended fpc thickness = 0.3 0.05mm gold plated (under 30 pos.), 0.3 0.03mm gold plated (over 31 pos.) 4. durability (insertion/ withdrawal) 5. vibration 6. shock 7. humidity (steady state) 8. temperature cycle 9. resistance to soldering heat 3. contact resistance 1. insulation resistance 2. withstanding voltage item specification conditions note 1: includes temperature rise caused by current flow. note 2: the term storage refers to products stored for long period of time prior to mounting and use. operating temperature r ange and humidity range covers non- conducting condition of installed connectors in storage, shipment or during transportation. note 3: information contained in this catalog represents general requirements for this series. contact us for the drawings and specifications for a specific part number shown. 2 fh33 series 0.4mm,0.5mm,1mm pitch, 1.2mm above the board, flexible printed circuit & flexible flat cable zif connectors 10 11 12 1 3 4 2 5 6 7 8 9 3 blank:standard j:halogen-free flame retardance ul94v-0 standard type:nomber of contacts eccentric type:number of contacts in 1mm housing 5 blank:width 3.0mm(standard) h:width 3.5mm(long actuator type) 4 6 contact alignment:s: single eccentric direction: blank:standard type b:eccentric type 8 standard type:blank eccentric type:nomber of contacts 9 plating specifications: blank:gold plated (10) gold plated with nickel barrier contact pitch: 0.4mm,0.5mm,1mm sh:smt horizontal mounting 12 10 11 7
3 fh33 series 0.4mm,0.5mm,1mm pitch, 1.2mm above the board, flexible printed circuit & flexible flat cable zif connectors 0.15 d0.1 2.250.15 u g number of contacts t b a0.15 (c: fpc insertion slot dimension) (0.15) (0.15) f number of contacts indicator polarizing mark indicator a** (1) lot no. indicator g 3 12 12 0 0.50.1 (1.1) 1.730.2 2.20.15 0.550.1 0.3 +0.15 C 0.1 0.250.1 0.15max 1.20.1 (1.8) (120?) 0.15max 0.350.1 a 0 connector dimensions notes the coplanarity of each terminal lead is within 0.1 max. the contact terminal lead position indicates the dimension from the bottom a surface of the insulator body. difference of each terminal lead is within 0.1 max. slight variations in color of the plastic compounds do not affect form, fit or function of the connector. after reflow, the terminal plating may change color, however this does not represent a quality issue. 1 2 3 4 5 6 unit: mm note 1: (**) : plating specification. refer to ordering information. note 2: tape-and-reel packaging (5,000 pieces/reel). order by number of reels. part number fh33-6s-0.5sh (**) fh33-9s-0.5sh (**) fh33-10s-0.5sh (**) fh33-12s-0.5sh (**) fh33-14s-0.5sh (**) fh33-19s-0.5sh (**) fh33-20s-0.5sh (**) fh33-26s-0.5sh (**) fh33-28s-0.5sh (**) fh33-30s-0.5sh (**) fh33-32s-0.5sh (**) fh33-36s-0.5sh (**) fh33-40s-0.5sh (**) fh33-45s-0.5sh (**) fh33m-16s-0.4sh (**) fh33j-4s-0.5sh (**) fh33j-10s-0.5sh (**) fh33j-12s-0.5sh (**) fh33j-16s-0.5sh (**) fh33j-18s-0.5sh (**) fh33j-19s-0.5sh (**) fh33j-40s-0.5sh (**) fh33mhj-65s-0.4sh (**) 580-1301-1-** 580-1303-7-** 580-1304-0-** 580-1302-4-** 580-1305-2-** 580-1307-8-** 580-1317-1-** 580-1306-5-** 580-1300-9-** 580-1312-8-** 580-1310-2-** 580-1311-5-** 580-1308-0-** 580-1316-9-** 580-1319-7-** 580-1329-0-** 580-1324-7-** 580-1328-8-** 580-1331-2-** 580-1334-0-** 580-1332-5-** 580-1330-0-** 580-1325-0-** 6 9 10 12 14 19 20 26 28 30 32 36 40 45 16 4 10 12 16 18 19 40 65 5 6.5 7 8 9 11.5 12 15 16 17 18 20 22 24.5 8.3 4 7 8 10 11 11.5 22 27.9 2.5 4 4.5 5.5 6.5 9 9.5 12.5 13.5 14.5 15.5 17.5 19.5 22 6 1.5 4.5 5.5 7.5 8.5 9 19.5 25.6 3.57 5.07 5.57 6.57 7.57 10.07 10.57 13.57 14.57 15.57 16.57 18.57 20.57 23.07 6.87 2.57 5.57 6.57 8.57 9.57 10.07 20.57 26.47 4.35 5.85 6.35 7.35 8.35 10.85 11.35 14.35 15.35 16.35 17.35 19.35 21.35 23.85 7.65 3.35 6.35 7.35 9.35 10.35 10.85 21.35 27.25 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.4 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.4 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.95 cl no. number of contacts a b c d t u f 0.4mm pitch, 0.5mm pitch type
4 fh33 series 0.4mm,0.5mm,1mm pitch, 1.2mm above the board, flexible printed circuit & flexible flat cable zif connectors a ? ? 1.75 v 1 0.45 2.250.15 0.15 b a0.15 1 0.15 (c: fpc insertion slot dimension) d0.1 0.15 g g number of contacts f lot no. indicator polarizing mark indicator number of contacts indicator hrs mark cav no. connector dimensions unit: mm part number fh33-4s-1sh(**) fh33-12(6)sb-1sh(**) fh33j-12(6)sb-1sh(**) 580-1322-1- ** 580-1323-4- ** 580-1326-2- ** 4 6 6 cl no. number of contacts 6.5 8 8 a 3 5 5 b 5.07 6.57 6.57 c 5.85 7.35 7.35 1.75 1.25 1.25 d v 3 12 12 0 0.50.1 (1.1) 1.730.2 2.20.15 0.550.1 0.3 +0.15 _0.1 0.250.1 0.15max 1.20.1 (1.8) 0.15max 0.350.1 a 0 ' note 1: (**) : plating specification. refer to ordering information. note 2: tape-and-reel packaging (5,000 pieces/reel). order by number of reels. notes the coplanarity of each terminal lead is within 0.1 max. the contact terminal lead position indicates the dimension from the bottom a surface of the insulator body. difference of each terminal lead is within 0.1 max. slight variations in color of the plastic compounds do not affect form, fit or function of the connector. after reflow, the terminal plating may change color, however this does not represent a quality issue. 1 2 3 4 5 6 1mm pitch type
5 fh33 series 0.4mm,0.5mm,1mm pitch, 1.2mm above the board, flexible printed circuit & flexible flat cable zif connectors b 0.250.05(metal mask) 0.1 h h (0.2) (a) (2.45) j0.1 k0.1 0.80.05 2.80.05 (0.15) (2.15) (0.15) (0.2) (0.2) number of contacts 0.30.05(land) t 0.650.05 * 3fdpnnfoefenfubmnbtluijdlofttnn 0.30.03 0.30.05 3.3min(stiffener) 2-r0.2 t0.07 e 0.30.03(ffc) 0.270.03(0.4mm pitch) b0.03 t0.03 l0.05 0.350.03(fpc) 2.30.3(exposed area) recommended pcb mounting pattern and metal mask dimensions recommended fpc dimensions note 1: if the stiffener is less than 3.3 mm, e dimension must be 0.5 mm min. unit: mm part number fh33-6s-0.5sh (**) fh33-9s-0.5sh (**) fh33-10s-0.5sh (**) fh33-12s-0.5sh (**) fh33-14s-0.5sh (**) fh33-19s-0.5sh (**) fh33-20s-0.5sh (**) fh33-26s-0.5sh (**) fh33-28s-0.5sh (**) fh33-30s-0.5sh (**) fh33-32s-0.5sh (**) fh33-36s-0.5sh (**) fh33-40s-0.5sh (**) fh33-45s-0.5sh (**) fh33m-16s-0.4sh (**) fh33j-4s-0.5sh (**) fh33j-10s-0.5sh (**) fh33j-12s-0.5sh (**) fh33j-16s-0.5sh (**) fh33j-18s-0.5sh (**) fh33j-19s-0.5sh (**) fh33j-40s-0.5sh (**) fh33mhj-65s-0.4sh (**) 580-1301-1-** 580-1303-7-** 580-1304-0-** 580-1302-4-** 580-1305-2-** 580-1307-8-** 580-1317-1-** 580-1306-5-** 580-1300-9-** 580-1312-8-** 580-1310-2-** 580-1311-5-** 580-1308-0-** 580-1316-9-** 580-1319-7- ** 580-1329-0- ** 580-1324-7- ** 580-1328-8- ** 580-1331-2- ** 580-1334-0- ** 580-1332-5- ** 580-1330-0- ** 580-1325-0- ** 6 9 10 12 14 19 20 26 28 30 32 36 40 45 16 4 10 12 16 18 19 40 65 5 6.5 7 8 9 11.5 12 15 16 17 18 20 22 24.5 8.3 4 7 8 10 11 11.5 22 27.9 2.5 4 4.5 5.5 6.5 9 9.5 12.5 13.5 14.5 15.5 17.5 19.5 22 6 1.5 4.5 5.5 7.5 8.5 9 19.5 25.6 3.8 5.3 5.8 6.8 7.8 10.3 10.8 13.8 14.8 15.8 16.8 18.8 20.8 23.3 7.1 2.8 5.8 6.8 8.8 9.8 10.3 20.8 26.7 4.9 6.4 6.9 7.9 8.9 11.4 11.9 14.9 15.9 16.9 17.9 19.9 21.9 24.4 8.2 3.9 6.9 7.9 9.9 10.9 11.4 21.9 27.8 3.5 5 5.5 6.5 7.5 10 10.5 13.5 14.5 15.5 16.5 18.5 20.5 23 6.8 2.5 5.5 6.5 8.5 9.5 10 20.5 26.4 cl no. number of contacts a b j k l 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.4 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.4 t 0.4mm pitch, 0.5mm pitch type 0.4mm pitch, 0.5mm pitch type
j 6 fh33 series 0.4mm,0.5mm,1mm pitch, 1.2mm above the board, flexible printed circuit & flexible flat cable zif connectors a k0.1 j0.1 1.150.1 w0.1 1 b 0.30.05(land) 0.250.05(metal mask) 0.15 2.15 2.45 0.15 0.2 0.2 0.2 2.80.05 0.650.05 0.80.05 h h number of contacts * 3fdpnnfoefenfubmnbtluijdlofttnn recommended pcb mounting pattern and metal mask dimensions 1mm pitch type 2-r0.2 10.1 0.650.1 10.1 x0.1 b0.1 l0.1 0.30.05 0.30.03 3.3min(stiffener) 2.30.3(exposed area) e recommended fpc dimensions 1mm pitch type unit: mm part number fh33-4s-1sh(**) fh33-12(6)sb-1sh(**) fh33j-12(6)sb-1sh(**) 580-1322-1- ** 580-1323-4- ** 580-1326-2- ** 4 6 6 cl no. number of contacts 6.5 8 8 a 3 5 5 b 5.3 6.8 6.8 6.4 7.9 7.9 5 6.5 6.5 1.15 0.65 0.65 1 0.5 0.5 k l w x
7 fh33 series 0.4mm,0.5mm,1mm pitch, 1.2mm above the board, flexible printed circuit & flexible flat cable zif connectors fh33 series fpc/ffc construction (recommended specifications) 1. using single-sided fpc material name covering film layer cover adhesive surface treatment copper foil base adhesive base film reinforcement material adhesive stiffener polyimide 1 mil thick nickel under plated 1 to 5m / gold plated 0.2m cu 1oz heat-hardened adhesive polyimide 1 mil thick heat-hardened adhesive polyimide 7 mil thick total (25) (25) 3 35 25 25 30 175 293 material thickness (m) 2. using double-sided fpc material name covering film layer cover adhesive surface treatment through-hole copper copper foil base adhesive base film base adhesive copper foil cover adhesive covering film layer reinforcement material adhesive stiffener polyimide 1 mil thick nickel under plated 1 to 5m / gold plated 0.2m cu cu 1/2oz heat-hardened adhesive polyimide 1 mil thick heat-hardened adhesive cu 1/2oz polyimide 1 mil thick heat-hardened adhesive polyimide 4 mil thick total (25) (25) 3 15 18 18 25 18 18 25 25 50 100 297 material thickness (m) 1. this specification is a recommendation for the construction of the fh12 series fpc and ffc (t=0.3 0.05). 2. for details about the construction, please contact the fpc/ffc manufacturers. practical tolerance of thickness dimension is 20 m 3. using ffc 4. precautions gold plated, soft copper film adhesive polyester adhesive stiffener polyester film adhesive polyester polyester polyester total polyester thermoplastic type ( 12 ) ( 30 ) 35 30 12 30 188 295 material name material thickness (m)
(?13) (?80) (?380) (r:inside) (s:outside) end section mounting section embossed carrier tape blank section lead section (400 mm min.) blank section top cover tape (10 pockets min.) (10 pockets min.) 8 fh33 series 0.4mm,0.5mm,1mm pitch, 1.2mm above the board, flexible printed circuit & flexible flat cable zif connectors note: 5,000 pieces per reel. embossed tape 32 mm or wider will have perforated feed holes on two sides. reel dimensions packaging specifications embossed carrier tape dimensions (tape width up to 24mm) embossed carrier tape dimensions (tape width 32mm and over) m0.3 1.750.1 flat surface for placement with automatic equipment (1) 80.1 20.15 n0.1 ?1.5 + 0 .1 0 unreeling direction (0.3) (q) (1.7) (3) (3.8) 40.1 flat surface for placement with automatic equipment (1) unreeling direction 1.750.1 ?1.5 + 0 .1 0 (0.3) m0.3 n0.1 p0.1 (q) 1.7 +0.15 0 1.5 +0.1 0 (1.7) 80.1 20.15 40.1 (3) (3.8)
9 fh33 series 0.4mm,0.5mm,1mm pitch, 1.2mm above the board, flexible printed circuit & flexible flat cable zif connectors unit: mm part number fh33-6s-0.5sh (**) fh33-9s-0.5sh (**) fh33-10s-0.5sh (**) fh33-12s-0.5sh (**) fh33-14s-0.5sh (**) fh33-19s-0.5sh (**) fh33-20s-0.5sh (**) fh33-26s-0.5sh (**) fh33-28s-0.5sh (**) fh33-30s-0.5sh (**) fh33-32s-0.5sh (**) fh33-36s-0.5sh (**) fh33-40s-0.5sh (**) fh33-45s-0.5sh (**) fh33m-16s-0.4sh (**) fh33j-4s-0.5sh (**) fh33j-10s-0.5sh (**) fh33j-12s-0.5sh (**) fh33j-16s-0.5sh (**) fh33j-18s-0.5sh (**) fh33j-19s-0.5sh (**) fh33j-40s-0.5sh (**) fh33mhj-65s-0.4sh (**) fh33-4s-1sh (**) fh33-12(6)s-1sh (**) fh33j-12(6)s-1sh (**) 580-1301-1-** 580-1303-7-** 580-1304-0-** 580-1302-4-** 580-1305-2-** 580-1307-8-** 580-1317-1-** 580-1306-5-** 580-1300-9-** 580-1312-8-** 580-1310-2-** 580-1311-5-** 580-1308-0-** 580-1316-9-** 580-1319-7- ** 580-1329-0- ** 580-1324-7- ** 580-1328-8- ** 580-1331-2- ** 580-1334-0- ** 580-1332-5- ** 580-1330-0- ** 580-1325-0- ** 580-1322-1- ** 580-1323-4- ** 580-1326-2- ** 6 9 10 12 14 19 20 26 28 30 32 36 40 45 16 4 10 12 16 18 19 40 65 4 6 6 16 16 16 16 16 24 24 24 24 24 32 32 44 44 24 16 16 16 24 24 24 44 44 16 16 16 7.5 7.5 7.5 7.5 7.5 11.5 11.5 11.5 11.5 11.5 14.2 14.2 20.2 20.2 11.5 7.5 7.5 7.5 11.5 11.5 11.5 20.2 20.2 7.5 7.5 7.5 -------- -------- -------- -------- -------- -------- -------- -------- -------- -------- 28.4 28.4 40.4 40.4 -------- -------- -------- -------- -------- -------- -------- 40.4 40.4 -------- -------- -------- 5.3 6.8 7.3 8.3 9.3 11.8 12.3 15.3 16.3 17.3 18.3 20.3 22.3 24.8 8.6 4.3 7.3 8.3 10.3 11.3 11.8 22.3 28.2 6.8 8.3 8.3 cl no. number of contacts m n p q 17.4 17.4 17.4 17.4 17.4 25.4 25.4 25.4 25.4 25.4 33.4 33.4 45.4 45.4 25.4 17.4 17.4 17.4 25.4 25.4 25.4 45.4 45.4 17.4 17.4 17.4 21.4 21.4 21.4 21.4 21.4 29.4 29.4 29.4 29.4 29.4 37.4 37.4 49.4 49.4 29.4 21.4 21.4 21.4 29.4 29.4 29.4 49.4 49.4 21.4 21.4 21.4 r s note 1: tape-and-reel packaging (5,000 pieces/reel). order by number of reels.
10 fh33 series 0.4mm,0.5mm,1mm pitch, 1.2mm above the board, flexible printed circuit & flexible flat cable zif connectors recommended temperature profile using lead-free solder paste max 250? start temperature (?) time (seconds) 25? (60 sec.) (60 sec.) 90 to 120 sec. preheating sodering 0 50 100 150 150? 200? 230? 200 250 hrs test conditions solder method : reflow, ir/hot air environment : room air solder composition : paste, 96.5%sn/3.0%ag/0.5%cu (senju metal industry, co., ltd.s part number: m705-221cm5-32-10.5) test board : glass epoxy 25mm50mm0.8mm thick land dimensions : contacts lead 0.3mm0.65mm metal fittings 0.55mm0.8mm metal mask : contacts lead 0.25mm0.65mm0.1mm thick metal fittings 0.55mm0.8mm0.1mm thick this temperature profile is based on the above conditions. in individual applications the actual temperature may vary, depending on solder paste type, volume/thickness and board size/thickness. consult your solder paste and equipment manufacturer for specific recommendations.
11 fh33 series 0.4mm,0.5mm,1mm pitch, 1.2mm above the board, flexible printed circuit & flexible flat cable zif connectors operation and precautions operation 1.fpc insertion procedure. connector installed on the board. lift up the actuator. use thumb or index finger. 1 2.fpc removal lift up the actuator. carefully withdraw the fpc. 1 fully insert the fpc in the connector parallel to mounting surface, with the exposed conductive traces facing down. 2 rotate down the actuator until firmly closed. it is critical that the inserted fpc is not moved and remains fully inserted. 3 fpc conductor surface (bottom side)
12 fh33 series 0.4mm,0.5mm,1mm pitch, 1.2mm above the board, flexible printed circuit & flexible flat cable zif connectors axis of rotation (120?) damege to the contacts damage to the contacts precautions exercise care when handling connectors. follow recommendations given below. pc board flexing s pc board connector mounting area the connectors are straight within 0.1 mm max. make sure that the pc board connector mounting area flatness can accept the connector terminals without causing any failure of the solder joints. s handling before mounting on pcb insertion of the fpc or operation of the actuator prior to mounting on the pcb is not recommended. s pc board handling exercise caution when handling boards with the connectors installed. do not apply any forces affecting soldered joints. precautions when inserting or removing fpc pay attention to the following points when inserting fpc. s actuator operation do not apply excessive force when opening the actuator prior to fpc insertion. when opening make sure that the force is applied only to the actuator itself, avoiding touching of the contacts. connector pcb assure free rotation of the actuator 1 axis of rotation 2 the actuator will rotate 120 degrees maximum. do not force it to rotate further. 3 120
13 fh33 series 0.4mm,0.5mm,1mm pitch, 1.2mm above the board, flexible printed circuit & flexible flat cable zif connectors actuator fpc precautions when operating the actuator, do so at the center portion. 4 as illustrated, do not attempt removal or re- positioning of the actuator. 5 s fpc insertion q the fpc should be aligned parallel with the board surface and perpendicular with the connector (as shown), then completely inserted. to assure correct electrical and mechanical connection do not insert fpc at angle. it must be fully inserted. make sure that the fpc is not moved during the closing of the actuator. perpendicular with the connector s fpc insertion w when inserting the fpc, do not forcefully rub against the bottom surface of the connector insertion entrance. doing so will result in the contacts and fpc making strong contact and may cause deformation of the contacts, peeling of the fpc conductor, and other problems. peeling of fpc conductor
14 precautions 120 other precautions s hand soldering precautions when hand soldering: do not perform reflow or hand soldering with the fpc inserted in the connector. do not apply excessive heat or touch the soldering iron anywhere other than the connector leads. do not use excessive amount of solder or flux compounds. operation of the actuator and contacts may be affected by excessive amounts of solder or flux compounds. 1 2 3 removing the fpc rotate the actuator to the open position (maximum open angle of 120). carefully withdraw the fpc. routing the fpc (fpc fully inserted/ actuator closed) s fpc load do not apply force in excess of 0.15n max. in the upward direction (as illustrated). do not bend the fpc too close to the actuator. load: 0.15n max. s verification of the fully closed actuator. the actuator should be fully closed (as illustrated) and the fpc held firmly in the connector. do not press against the actuator when is fully closed. max force applied to the fully closed actuator should not exceed 1 n. fh33 series 0.4mm,0.5 mm,1mm pitch, 1.2 mm above the board, flexible printed circuit & flexible flat cable zif connectors
15 fh33 series 0.4mm,0.5mm,1mm pitch, 1.2mm above the board, flexible printed circuit & flexible flat cable zif connectors notes :
16 fh33 series 0.4mm,0.5mm,1mm pitch, 1.2mm above the board, flexible printed circuit & flexible flat cable zif connectors the contents of this catalog are current as of date of 03/2012. contents are subject to change without notice for the purpose o f improvements. usa: hirose electric (u.s.a.), inc. san jose office 20400 stevens creek blvd., ste 250, cupertino, ca 95014 phone : +1-408-253-9640 fax : +1-408-253-9641 http://www.hiroseusa.com usa: hirose electric (u.s.a.), inc. headquarters 2688 westhills court, simi valley, ca 93065-6235 phone : +1-805-522-7958 fax : +1-805-522-3217 http://www.hiroseusa.com hong kong: hirose electric hongkong trading co., ltd. room 1001, west wing, tsim sha tsui centre, 66 mody road, tsim sha tsui east, kowloon, hong kong phone : +852-2803-5338 fax : +852-2591-6560 http://www.hirose-hongkong.com.hk china: hirose electric (shanghai) co., ltd. beijing branch a1001, ocean international center, building 56# east 4th ring middle road, chao yang district, beijing, 100025 phone : +86-10-5165-9332 fax : +86-10-5908-1381 http://www.hirose-china.com.cn taiwan: hirose electric taiwan co., ltd. 103 8f, no.87, zhengzhou rd., taipei phone : +886-2-2555-7377 fax : +886-2-2555-7350 http://www.hirose-taiwan.com.tw germany: hirose electric europe b.v. german branch herzog-carl-strasse 4 d-73760 ostfildern (scharnhauser park) phone : +49-711-4560-02-1 fax : +49-711-4560-02-299 http://www.hirose.de india: hirose electric singapore pte. ltd. bangalore liaison office unit no.03, ground floor, explorer building international tech park whitefield road, bangalore 560066 karnataka, india phone : +65-6324-6113 fax : +65-6324-6123 http://www.hirose-singapore.com.sg singapore: hirose electric singapore pte. ltd. 10 anson road #26-16 international plaza 079903 phone : +65-6324-6113 fax : + 65-6324-6123 http://www.hirose-singapore.com.sg the netherlands: hirose electric europe b.v. hogehillweg #8 1101 cc amsterdam z-o phone : +31-20-6557460 fax : +31-20-6557469 http://www.hiroseeurope.com united kingdom: hirose electric europe b.v. uk branch first floor, st andrews house, caldecotte lake business park, milton keynes mk7 8le phone : +44-1908-369060 fax : +44-1908-369078 http://www.hirose.co.uk usa: hirose electric (u.s.a.), inc. detroit office (automotive) 37677 professional center drive, suite #100c livonia, mi 48154 phone : +1-734-542-9963 fax : +1-734-542-9964 http://www.hiroseusa.com china: hirose electric (shanghai) co., ltd. 1601,henderson metropolitan,no.300 ,east nanjing road,huangpu district, shanghai,china 200001 phone : +86-21-6391-3355 fax : +86-21-6391-3335 http://www.hirose-china.com.cn china: hirose electric technologies (shenzhen) co., ltd. room 09-13, 19/f, office tower shun hing square, di wang commercial centre 5002, shennandong road, shenzhen city, guangdong province, 518008 phone : +86-755-8207-0851 fax : +86-755-8207-0873 http://www.hirose-china.com.cn korea: hirose korea co., ltd. 1261-10, jeoungwhang-dong, shihung-city, kyunggi-do 429-450 phone : +82-31-496-7000,7124 fax : +82-31-496-7100 http://www.hirose.co.kr 6-3,nakagawa chuoh-2-chome,tsuzuki-ku,yokohama-shi 224-8540,japan tel: + 81-45-620-3526 fax: + 81-45-591-3726 http://www.hirose.com http://www.hirose-connectors.com ?

▲Up To Search▲

Price & Availability of FH33MHJ-65S-04SH

	To Download FH33MHJ-65S-04SH Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .